|
|
Модуль Bosch EDC17CP09 BitEdit
Модуль Bosch EDC17CP09 BitEdit
Модуль для калибровки прошивок блоков управления Bosch EDC17CP09 дизельных автомобилей BMW.
Поддерживается размер файлов 4мб.
Доступны следующие карты:
Airmass: desired airmass flow with enabled and disabled EGR, maximal airmass flow, airmass correction
Boost control: boost controller duty cycle base, in regeneration, in double injection mode, with disabled EGR, maximal boost controller duty cycle
Boost pressure: boost pressure limitation, desired boost pressure base, in regeneration, in double injection mode, with disabled EGR, with closed bypass
DPF: Enable switches for DPF, regeneration lookup mask, exhaust sensor scaling and check conditions
EGR control: thresholds for enable/disable EGR
EGT Sensors: EGT sensors scalings, switches and check conditions
Injection: injection quantity from torque conversion maps, injector opening time, post injection quantity
Rail pressure: Rail pressure base, at idle, rail pressure limiters, P, I components for flow regulator, injection flow regulator map, rail pressure regulator maps
Start: engine speed after start, start torque, minimal engine speed
Start of injection: base start of injection angle for main injection, time component between Pi1 and Pi2
Target lambda for smoke limitation
Torque limitation: torque limitation inner/outer torque, powertrain torque, conditional torque limitation from EGT, exhaust pressure, fuel temperature, torque limitation in system errors.
Torque monitoring: torque limitation in monitoring mode, accelerator pedal for monitoring
Requested torque: requested torque from accelerator pedal base, requested torque correction factors from coolant and atmospheric pressure
DTC editor
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Bosch EDC17CP09
License cost: 200.00 Eur.
Software module for editing calibrations Bosch EDC17CP09 ECUs of diesel BMW vehicles.
Supported filesize 4Mb.
Available maps:
Airmass: desired airmass flow with enabled and disabled EGR, maximal airmass flow, airmass correction
Boost control: boost controller duty cycle base, in regeneration, in double injection mode, with disabled EGR, maximal boost controller duty cycle
Boost pressure: boost pressure limitation, desired boost pressure base, in regeneration, in double injection mode, with disabled EGR, with closed bypass
DPF: Enable switches for DPF, regeneration lookup mask, exhaust sensor scaling and check conditions
EGR control: thresholds for enable/disable EGR
EGT Sensors: EGT sensors scalings, switches and check conditions
Injection: injection quantity from torque conversion maps, injector opening time, post injection quantity
Rail pressure: Rail pressure base, at idle, rail pressure limiters, P, I components for flow regulator, injection flow regulator map, rail pressure regulator maps
Start: engine speed after start, start torque, minimal engine speed
Start of injection: base start of injection angle for main injection, time component between Pi1 and Pi2
Target lambda for smoke limitation
Torque limitation: torque limitation inner/outer torque, powertrain torque, conditional torque limitation from EGT, exhaust pressure, fuel temperature, torque limitation in system errors.
Torque monitoring: torque limitation in monitoring mode, accelerator pedal for monitoring
Requested torque: requested torque from accelerator pedal base, requested torque correction factors from coolant and atmospheric pressure
DTC editor.
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Модуль Bosch EDC17CP09 BitEdit
Модуль для калибровки прошивок блоков управления Bosch EDC17CP09 дизельных автомобилей BMW.
Поддерживается размер файлов 4мб.
Доступны следующие карты:
Airmass: desired airmass flow with enabled and disabled EGR, maximal airmass flow, airmass correction
Boost control: boost controller duty cycle base, in regeneration, in double injection mode, with disabled EGR, maximal boost controller duty cycle
Boost pressure: boost pressure limitation, desired boost pressure base, in regeneration, in double injection mode, with disabled EGR, with closed bypass
DPF: Enable switches for DPF, regeneration lookup mask, exhaust sensor scaling and check conditions
EGR control: thresholds for enable/disable EGR
EGT Sensors: EGT sensors scalings, switches and check conditions
Injection: injection quantity from torque conversion maps, injector opening time, post injection quantity
Rail pressure: Rail pressure base, at idle, rail pressure limiters, P, I components for flow regulator, injection flow regulator map, rail pressure regulator maps
Start: engine speed after start, start torque, minimal engine speed
Start of injection: base start of injection angle for main injection, time component between Pi1 and Pi2
Target lambda for smoke limitation
Torque limitation: torque limitation inner/outer torque, powertrain torque, conditional torque limitation from EGT, exhaust pressure, fuel temperature, torque limitation in system errors.
Torque monitoring: torque limitation in monitoring mode, accelerator pedal for monitoring
Requested torque: requested torque from accelerator pedal base, requested torque correction factors from coolant and atmospheric pressure
DTC editor
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Bosch EDC17CP09
License cost: 200.00 Eur.
Software module for editing calibrations Bosch EDC17CP09 ECUs of diesel BMW vehicles.
Supported filesize 4Mb.
Available maps:
Airmass: desired airmass flow with enabled and disabled EGR, maximal airmass flow, airmass correction
Boost control: boost controller duty cycle base, in regeneration, in double injection mode, with disabled EGR, maximal boost controller duty cycle
Boost pressure: boost pressure limitation, desired boost pressure base, in regeneration, in double injection mode, with disabled EGR, with closed bypass
DPF: Enable switches for DPF, regeneration lookup mask, exhaust sensor scaling and check conditions
EGR control: thresholds for enable/disable EGR
EGT Sensors: EGT sensors scalings, switches and check conditions
Injection: injection quantity from torque conversion maps, injector opening time, post injection quantity
Rail pressure: Rail pressure base, at idle, rail pressure limiters, P, I components for flow regulator, injection flow regulator map, rail pressure regulator maps
Start: engine speed after start, start torque, minimal engine speed
Start of injection: base start of injection angle for main injection, time component between Pi1 and Pi2
Target lambda for smoke limitation
Torque limitation: torque limitation inner/outer torque, powertrain torque, conditional torque limitation from EGT, exhaust pressure, fuel temperature, torque limitation in system errors.
Torque monitoring: torque limitation in monitoring mode, accelerator pedal for monitoring
Requested torque: requested torque from accelerator pedal base, requested torque correction factors from coolant and atmospheric pressure
DTC editor.
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Если у Вас возникли вопросы по данному товару, задавайте их через форму ниже.
BitEdit
| ЧИП-ТЮНИНГ ЭБУ
« Назад
|
