|
|
Модуль Extreme vehicles Bosch MSE6.0/US6.0 к BitEdit
Модуль Bosch MSE6.0/US6.0 к BitEdit
Модуль для калибровки прошивок блоков управления Bosch MSE6.0/US6.0, используемых в различных видах мототехники.
Для редактирования доступны следующие карты:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error, Target air filling calculated, Throttle valve position from airmass flow
Airmass calculation: efficiency: Exhaust gas rest pressure, Volumetric efficiency
Exhaust gas model: Exhaust gas temperature in additional mode
Idle speed control: Desired idle speed, Desired idle speed in warm up, Elevated idle speed from battery voltage
Injector control: Injection end timing, Injection end timing full load, Injection end timing at start, Injection end timing at start by engine speed, Injection end timing cold engine, Injector dead time, Injector flow constant
Limiters: Engine speed limitation, Vehicle Speed Limitation (Test if found, not guaranteed)
Spark advance: Spark advance optimal, Spark advance base, Spark advance correction by coolant temperature
Start: Cold start enrichment, Injection correction factor for reducing enrichment on cold start, Injection correction factor for reducing enrichment on warm start, Warm start enrichment
Target lambda: Lambda configuration bitmask (0 - no lambda, 1 - front, 3 - both), Lambda Limit for combustion, Lean lambda threshold by coolant temperature, Pulsations correction factor, Target lambda at full load, Target Lambda at Partial Load, Target lambda at warm up, Target lambda on acceleration hot engine
DTC
Список поддерживаемых версий ПО
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Bosch MSE6.0/US6.0
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error, Target air filling calculated, Throttle valve position from airmass flow
Airmass calculation: efficiency: Exhaust gas rest pressure, Volumetric efficiency
Exhaust gas model: Exhaust gas temperature in additional mode
Idle speed control: Desired idle speed, Desired idle speed in warm up, Elevated idle speed from battery voltage
Injector control: Injection end timing, Injection end timing full load, Injection end timing at start, Injection end timing at start by engine speed, Injection end timing cold engine, Injector dead time, Injector flow constant
Limiters: Engine speed limitation, Vehicle Speed Limitation (Test if found, not guaranteed)
Spark advance: Spark advance optimal, Spark advance base, Spark advance correction by coolant temperature
Start: Cold start enrichment, Injection correction factor for reducing enrichment on cold start, Injection correction factor for reducing enrichment on warm start, Warm start enrichment
Target lambda: Lambda configuration bitmask (0 - no lambda, 1 - front, 3 - both), Lambda Limit for combustion, Lean lambda threshold by coolant temperature, Pulsations correction factor, Target lambda at full load, Target Lambda at Partial Load, Target lambda at warm up, Target lambda on acceleration hot engine
DTC
Supported SW list
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Модуль Bosch MSE6.0/US6.0 к BitEdit
Модуль для калибровки прошивок блоков управления Bosch MSE6.0/US6.0, используемых в различных видах мототехники.
Для редактирования доступны следующие карты:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error, Target air filling calculated, Throttle valve position from airmass flow
Airmass calculation: efficiency: Exhaust gas rest pressure, Volumetric efficiency
Exhaust gas model: Exhaust gas temperature in additional mode
Idle speed control: Desired idle speed, Desired idle speed in warm up, Elevated idle speed from battery voltage
Injector control: Injection end timing, Injection end timing full load, Injection end timing at start, Injection end timing at start by engine speed, Injection end timing cold engine, Injector dead time, Injector flow constant
Limiters: Engine speed limitation, Vehicle Speed Limitation (Test if found, not guaranteed)
Spark advance: Spark advance optimal, Spark advance base, Spark advance correction by coolant temperature
Start: Cold start enrichment, Injection correction factor for reducing enrichment on cold start, Injection correction factor for reducing enrichment on warm start, Warm start enrichment
Target lambda: Lambda configuration bitmask (0 - no lambda, 1 - front, 3 - both), Lambda Limit for combustion, Lean lambda threshold by coolant temperature, Pulsations correction factor, Target lambda at full load, Target Lambda at Partial Load, Target lambda at warm up, Target lambda on acceleration hot engine
DTC
Список поддерживаемых версий ПО
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Bosch MSE6.0/US6.0
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error, Target air filling calculated, Throttle valve position from airmass flow
Airmass calculation: efficiency: Exhaust gas rest pressure, Volumetric efficiency
Exhaust gas model: Exhaust gas temperature in additional mode
Idle speed control: Desired idle speed, Desired idle speed in warm up, Elevated idle speed from battery voltage
Injector control: Injection end timing, Injection end timing full load, Injection end timing at start, Injection end timing at start by engine speed, Injection end timing cold engine, Injector dead time, Injector flow constant
Limiters: Engine speed limitation, Vehicle Speed Limitation (Test if found, not guaranteed)
Spark advance: Spark advance optimal, Spark advance base, Spark advance correction by coolant temperature
Start: Cold start enrichment, Injection correction factor for reducing enrichment on cold start, Injection correction factor for reducing enrichment on warm start, Warm start enrichment
Target lambda: Lambda configuration bitmask (0 - no lambda, 1 - front, 3 - both), Lambda Limit for combustion, Lean lambda threshold by coolant temperature, Pulsations correction factor, Target lambda at full load, Target Lambda at Partial Load, Target lambda at warm up, Target lambda on acceleration hot engine
DTC
Supported SW list
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Если у Вас возникли вопросы по данному товару, задавайте их через форму ниже.
BitEdit
| ЧИП-ТЮНИНГ ЭБУ
« Назад
|
