|
|
Модуль Continental GPEC3 к BitEdit
Модуль Continental GPEC3 к BitEdit
Модуль для калибровки систем управления бензиновых двигателей автомобилей Chrysler/Dodge/Jeep и Fiat с блоками управления Continental GPEC3.
Air calculation: Map for calculation of nominal charge, Volumetric efficiency at part load bank
Airflow correction: Airflow through throttle body, Coolant temperature factor for volumetric efficiency, Intake temperature factor for volumetric efficiency, Volumetric efficiency multiplier for coolant temperature, Volumetric efficiency multiplier for intake temperature
Closed loop: Closed loop enable delay bank
Idle speed: Desired idle speed in drive, Desired idle speed in drive (high octane), Elevated idle speed, Idle speed at drive, Idle speed in drive with AC, Idle speed in P/N, Idle speed in P/N with AC, Minimal idle speed at drive, Minimal idle speed at P/N, Minimal idle speed at P/N
Injection compensation: Fuel quantity injected, Lambda base value, Power enrichment at high octane, Power enrichment at regular octane
Injection control: Fuel mass by injection PWM, Injection PWM by fuel mass, Injection PWM offset
Limiters: Engine speed limitation, Engine speed limiter by engine coolant temperature, Engine speed limiter by oil temperature, Engine speed limiter in Neutral, Vehilce speed limitation
Spark advance: Optimal spark advance ignition angle in additional mode
Spark advance ignition angle base: Spark advance ignition angle base in additional mode, Spark advance minimum ignition angle
Spark Advance knock detection: Spark advance knock detection factor
Spark advance: corrections: Spark advance ignition angle correction by engine temperature
Spark advance: limits: Spark advance ignition angle limit
Temperature: Exhaust Gas Temperature
Throttle valve control: Throttle valve opening angle large range, Throttle valve opening angle small range
Torque: Maximum torque, Pedal accelerator by torque reques in additional mode, Torque limit by gear and speed, Torque request by accelerator pedal in additional mode
DTC
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Continental GPEC3
Software module for editing calibrations Chrysler/Dodge/Jeep vehicles with ECU Continental GPEC3.
Air calculation: Map for calculation of nominal charge, Volumetric efficiency at part load bank
Airflow correction: Airflow through throttle body, Coolant temperature factor for volumetric efficiency, Intake temperature factor for volumetric efficiency, Volumetric efficiency multiplier for coolant temperature, Volumetric efficiency multiplier for intake temperature
Closed loop: Closed loop enable delay bank
Idle speed: Desired idle speed in drive, Desired idle speed in drive (high octane), Elevated idle speed, Idle speed at drive, Idle speed in drive with AC, Idle speed in P/N, Idle speed in P/N with AC, Minimal idle speed at drive, Minimal idle speed at P/N, Minimal idle speed at P/N
Injection compensation: Fuel quantity injected, Lambda base value, Power enrichment at high octane, Power enrichment at regular octane
Injection control: Fuel mass by injection PWM, Injection PWM by fuel mass, Injection PWM offset
Limiters: Engine speed limitation, Engine speed limiter by engine coolant temperature, Engine speed limiter by oil temperature, Engine speed limiter in Neutral, Vehilce speed limitation
Spark advance: Optimal spark advance ignition angle in additional mode
Spark advance ignition angle base: Spark advance ignition angle base in additional mode, Spark advance minimum ignition angle
Spark Advance knock detection: Spark advance knock detection factor
Spark advance: corrections: Spark advance ignition angle correction by engine temperature
Spark advance: limits: Spark advance ignition angle limit
Temperature: Exhaust Gas Temperature
Throttle valve control: Throttle valve opening angle large range, Throttle valve opening angle small range
Torque: Maximum torque, Pedal accelerator by torque reques in additional mode, Torque limit by gear and speed, Torque request by accelerator pedal in additional mode
DTC
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Модуль Continental GPEC3 к BitEdit
Модуль для калибровки систем управления бензиновых двигателей автомобилей Chrysler/Dodge/Jeep и Fiat с блоками управления Continental GPEC3.
Air calculation: Map for calculation of nominal charge, Volumetric efficiency at part load bank
Airflow correction: Airflow through throttle body, Coolant temperature factor for volumetric efficiency, Intake temperature factor for volumetric efficiency, Volumetric efficiency multiplier for coolant temperature, Volumetric efficiency multiplier for intake temperature
Closed loop: Closed loop enable delay bank
Idle speed: Desired idle speed in drive, Desired idle speed in drive (high octane), Elevated idle speed, Idle speed at drive, Idle speed in drive with AC, Idle speed in P/N, Idle speed in P/N with AC, Minimal idle speed at drive, Minimal idle speed at P/N, Minimal idle speed at P/N
Injection compensation: Fuel quantity injected, Lambda base value, Power enrichment at high octane, Power enrichment at regular octane
Injection control: Fuel mass by injection PWM, Injection PWM by fuel mass, Injection PWM offset
Limiters: Engine speed limitation, Engine speed limiter by engine coolant temperature, Engine speed limiter by oil temperature, Engine speed limiter in Neutral, Vehilce speed limitation
Spark advance: Optimal spark advance ignition angle in additional mode
Spark advance ignition angle base: Spark advance ignition angle base in additional mode, Spark advance minimum ignition angle
Spark Advance knock detection: Spark advance knock detection factor
Spark advance: corrections: Spark advance ignition angle correction by engine temperature
Spark advance: limits: Spark advance ignition angle limit
Temperature: Exhaust Gas Temperature
Throttle valve control: Throttle valve opening angle large range, Throttle valve opening angle small range
Torque: Maximum torque, Pedal accelerator by torque reques in additional mode, Torque limit by gear and speed, Torque request by accelerator pedal in additional mode
DTC
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Continental GPEC3
Software module for editing calibrations Chrysler/Dodge/Jeep vehicles with ECU Continental GPEC3.
Air calculation: Map for calculation of nominal charge, Volumetric efficiency at part load bank
Airflow correction: Airflow through throttle body, Coolant temperature factor for volumetric efficiency, Intake temperature factor for volumetric efficiency, Volumetric efficiency multiplier for coolant temperature, Volumetric efficiency multiplier for intake temperature
Closed loop: Closed loop enable delay bank
Idle speed: Desired idle speed in drive, Desired idle speed in drive (high octane), Elevated idle speed, Idle speed at drive, Idle speed in drive with AC, Idle speed in P/N, Idle speed in P/N with AC, Minimal idle speed at drive, Minimal idle speed at P/N, Minimal idle speed at P/N
Injection compensation: Fuel quantity injected, Lambda base value, Power enrichment at high octane, Power enrichment at regular octane
Injection control: Fuel mass by injection PWM, Injection PWM by fuel mass, Injection PWM offset
Limiters: Engine speed limitation, Engine speed limiter by engine coolant temperature, Engine speed limiter by oil temperature, Engine speed limiter in Neutral, Vehilce speed limitation
Spark advance: Optimal spark advance ignition angle in additional mode
Spark advance ignition angle base: Spark advance ignition angle base in additional mode, Spark advance minimum ignition angle
Spark Advance knock detection: Spark advance knock detection factor
Spark advance: corrections: Spark advance ignition angle correction by engine temperature
Spark advance: limits: Spark advance ignition angle limit
Temperature: Exhaust Gas Temperature
Throttle valve control: Throttle valve opening angle large range, Throttle valve opening angle small range
Torque: Maximum torque, Pedal accelerator by torque reques in additional mode, Torque limit by gear and speed, Torque request by accelerator pedal in additional mode
DTC
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Если у Вас возникли вопросы по данному товару, задавайте их через форму ниже.
BitEdit
| ЧИП-ТЮНИНГ ЭБУ
« Назад
|
