|
|
Модуль Continental SIM2K-26x
Модуль Continental SIM2K-26x
Модуль для калибровки прошивок блоков управления Continental SIM2K-260 и SIM2K-261 бензиновых атмосферных и турбированных автомобилей Kia/Hyundai.
Доступны следующие карты:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver request: Driver interpretation map
Exhaust camshaft position: Exhaust camshaft position setpoint
Exhaust gas temperature model: Basic engine out exhaust gas temperature for reference conditions, Basic ignition angle for the exhaust gas temperature model, Engine out exhaust gas temperature in case of full cylinder shut off after very long PUC duration, Reference ignition angle for the exhaust gas temperature model
Fuel pressure: Fuel pressure setpoint in additional mode
Idle speed: Nominal idle speed in additional mode
Ignition maps: Basic ignition angle, Basic minimum ignition angle difference value, Ignition correction via intake air temperature, Reference ignition angle
Intake camshaft position: Intake camshaft position in additional mode
Limiters [if found]: Maximum speed limiter (higher threshold), Maximum speed limiter (lower threshold)
Target Lambda: Lambda for component protection, Lambda full load enrichment, Reference lambda value
Throttle control: Manual throttle position setpoint, Maximum throttle position setpoint at ignition key on for non TCI and A/T
Torque model: Coolant and oil temperature correction of friction torque, Frictional and pumping torque losses of the engine, Indicated engine torque at reference conditions
Turbo system: Air Temperature increase factor through the turbocharger compressor, Basic wastegate EPC temperature, Limitation of PQ_SCHA, Map for boost pressure actuator setpoint, Maximum allowed pressure quotient at turbo charger compressor, Maximum charge air pressure quotient for charge air pressure too high (CAP_H) diagnosis, Maximum Pressure ratio at charger for activation of MAP_CTL plausibility diagnoses, Minimum charge air pressure quotient for charge air pressure too low (CAP_L) diagnosis, Open loop wastegate control signal, Pressure ratio at the wastegate actuator EPC, Pressure up throttle setpoint, Standardized turbocharger speed, Hysteresis value for end of surge definition - in idle, Maximum pressure up throttle at standard conditions, Surge line definition (component characteristic) for LV_SURGE detection
DTC
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Continental SIM2K-26x
License cost: 200.00 Eur.
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver request: Driver interpretation map
Exhaust camshaft position: Exhaust camshaft position setpoint
Exhaust gas temperature model: Basic engine out exhaust gas temperature for reference conditions, Basic ignition angle for the exhaust gas temperature model, Engine out exhaust gas temperature in case of full cylinder shut off after very long PUC duration, Reference ignition angle for the exhaust gas temperature model
Fuel pressure: Fuel pressure setpoint in additional mode
Idle speed: Nominal idle speed in additional mode
Ignition maps: Basic ignition angle, Basic minimum ignition angle difference value, Ignition correction via intake air temperature, Reference ignition angle
Intake camshaft position: Intake camshaft position in additional mode
Limiters [if found]: Maximum speed limiter (higher threshold), Maximum speed limiter (lower threshold)
Target Lambda: Lambda for component protection, Lambda full load enrichment, Reference lambda value
Throttle control: Manual throttle position setpoint, Maximum throttle position setpoint at ignition key on for non TCI and A/T
Torque model: Coolant and oil temperature correction of friction torque, Frictional and pumping torque losses of the engine, Indicated engine torque at reference conditions
Turbo system: Air Temperature increase factor through the turbocharger compressor, Basic wastegate EPC temperature, Limitation of PQ_SCHA, Map for boost pressure actuator setpoint, Maximum allowed pressure quotient at turbo charger compressor, Maximum charge air pressure quotient for charge air pressure too high (CAP_H) diagnosis, Maximum Pressure ratio at charger for activation of MAP_CTL plausibility diagnoses, Minimum charge air pressure quotient for charge air pressure too low (CAP_L) diagnosis, Open loop wastegate control signal, Pressure ratio at the wastegate actuator EPC, Pressure up throttle setpoint, Standardized turbocharger speed, Hysteresis value for end of surge definition - in idle, Maximum pressure up throttle at standard conditions, Surge line definition (component characteristic) for LV_SURGE detection
DTC
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Модуль Continental SIM2K-26x
Модуль для калибровки прошивок блоков управления Continental SIM2K-260 и SIM2K-261 бензиновых атмосферных и турбированных автомобилей Kia/Hyundai.
Доступны следующие карты:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver request: Driver interpretation map
Exhaust camshaft position: Exhaust camshaft position setpoint
Exhaust gas temperature model: Basic engine out exhaust gas temperature for reference conditions, Basic ignition angle for the exhaust gas temperature model, Engine out exhaust gas temperature in case of full cylinder shut off after very long PUC duration, Reference ignition angle for the exhaust gas temperature model
Fuel pressure: Fuel pressure setpoint in additional mode
Idle speed: Nominal idle speed in additional mode
Ignition maps: Basic ignition angle, Basic minimum ignition angle difference value, Ignition correction via intake air temperature, Reference ignition angle
Intake camshaft position: Intake camshaft position in additional mode
Limiters [if found]: Maximum speed limiter (higher threshold), Maximum speed limiter (lower threshold)
Target Lambda: Lambda for component protection, Lambda full load enrichment, Reference lambda value
Throttle control: Manual throttle position setpoint, Maximum throttle position setpoint at ignition key on for non TCI and A/T
Torque model: Coolant and oil temperature correction of friction torque, Frictional and pumping torque losses of the engine, Indicated engine torque at reference conditions
Turbo system: Air Temperature increase factor through the turbocharger compressor, Basic wastegate EPC temperature, Limitation of PQ_SCHA, Map for boost pressure actuator setpoint, Maximum allowed pressure quotient at turbo charger compressor, Maximum charge air pressure quotient for charge air pressure too high (CAP_H) diagnosis, Maximum Pressure ratio at charger for activation of MAP_CTL plausibility diagnoses, Minimum charge air pressure quotient for charge air pressure too low (CAP_L) diagnosis, Open loop wastegate control signal, Pressure ratio at the wastegate actuator EPC, Pressure up throttle setpoint, Standardized turbocharger speed, Hysteresis value for end of surge definition - in idle, Maximum pressure up throttle at standard conditions, Surge line definition (component characteristic) for LV_SURGE detection
DTC
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Continental SIM2K-26x
License cost: 200.00 Eur.
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver request: Driver interpretation map
Exhaust camshaft position: Exhaust camshaft position setpoint
Exhaust gas temperature model: Basic engine out exhaust gas temperature for reference conditions, Basic ignition angle for the exhaust gas temperature model, Engine out exhaust gas temperature in case of full cylinder shut off after very long PUC duration, Reference ignition angle for the exhaust gas temperature model
Fuel pressure: Fuel pressure setpoint in additional mode
Idle speed: Nominal idle speed in additional mode
Ignition maps: Basic ignition angle, Basic minimum ignition angle difference value, Ignition correction via intake air temperature, Reference ignition angle
Intake camshaft position: Intake camshaft position in additional mode
Limiters [if found]: Maximum speed limiter (higher threshold), Maximum speed limiter (lower threshold)
Target Lambda: Lambda for component protection, Lambda full load enrichment, Reference lambda value
Throttle control: Manual throttle position setpoint, Maximum throttle position setpoint at ignition key on for non TCI and A/T
Torque model: Coolant and oil temperature correction of friction torque, Frictional and pumping torque losses of the engine, Indicated engine torque at reference conditions
Turbo system: Air Temperature increase factor through the turbocharger compressor, Basic wastegate EPC temperature, Limitation of PQ_SCHA, Map for boost pressure actuator setpoint, Maximum allowed pressure quotient at turbo charger compressor, Maximum charge air pressure quotient for charge air pressure too high (CAP_H) diagnosis, Maximum Pressure ratio at charger for activation of MAP_CTL plausibility diagnoses, Minimum charge air pressure quotient for charge air pressure too low (CAP_L) diagnosis, Open loop wastegate control signal, Pressure ratio at the wastegate actuator EPC, Pressure up throttle setpoint, Standardized turbocharger speed, Hysteresis value for end of surge definition - in idle, Maximum pressure up throttle at standard conditions, Surge line definition (component characteristic) for LV_SURGE detection
DTC
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
BitEdit
« Назад
|
