|
|
Модуль Honda Keihin 1.5 NA BitEdit
Модуль Honda Keihin 1.5 NA BitEdit
Модуль для редактирования калибровок автомобилей Honda с атмосферными бензиновыми двигателями объемом 1.5 л и блоками управления Keihin на базе процессора TC1782.
Поддерживаемый размер файлов: 2.5Мб
Поддерживаемые карты:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge Efficiency Low VTEC, Airmass flow through throttle body in additional mode, Exhaust back pressure after catalyst, Airmass flow through throttle body direct
Camshaft control: Target camshaft angle High VTEC, Target camshaft angle Low VTEC, Camshaft Angle at WOT High VTEC, Camshaft Angle at WOT Low VTEC
EGT: EGT Prediction MAP by Air Intake A/B
Fuel: MAP Fuel High VTEC in additional mode, MAP Fuel Low VTEC in additional mode
Idle: Desired idle speed, Desired idle speed after start A, Desired idle speed after start B
Injector control: Injector scaling in additional mode
Knock Limit: Spark advance limitation for knocking High VTEC, Spark advance limitation for knocking Low VTEC
Knock sensitivity: Knock Sensitivity
Limiters: Engine speed limitation
Load limitation: Load limitation High VTEC, Load limitation Low VTEC
Overrun Cutoff: Overrun Injector Restart RPM Cut, Overrun Injector Restart RPM Recover
Sensors scaling: Lambda sensor conversion, Mass air flow sensor scaling
Spark advance: Spark advance EGR dependent High VTEC, Spark advance EGR dependent Low VTEC, Spark advance retardation to reduce torque High VTEC, Spark advance retardation to reduce torque Low VTEC, Dwell time, Ignition Dwell Angle
Spark advance corrections: Spark advance correction by intake temperature
Spark Compensation: Water Temperature Ignition Advance, Water Temperature Ignition Retard
Target Lambda: Target Lambda at full load, Target lambda in closed loop, Target lambda limit for closed loop
Throttle valve control: Driving Force in additional mode, Throttle valve position linearization High VTEC, Throttle valve position linearization Low VTEC, Enable throttle valve opening
Torque: Torque Limit Torque Limitation (Test, if found)
VTEC: Engine speed to enable VTEC (Test, if found)
Vehicle speed limitation - NO support!
DTC mask - NO support!
Список поддерживаемых версий ПО
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Honda Keihin 1.5 NA
Software module allows to edit calibrations of the Honda/Acura Petrol 1.5 normal aspirated vehicles with Keihin TC1782 ECUs.
Supported filesize: 2.5Mb.
Available maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge Efficiency Low VTEC, Airmass flow through throttle body in additional mode, Exhaust back pressure after catalyst, Airmass flow through throttle body direct
Camshaft control: Target camshaft angle High VTEC, Target camshaft angle Low VTEC, Camshaft Angle at WOT High VTEC, Camshaft Angle at WOT Low VTEC
EGT: EGT Prediction MAP by Air Intake A/B
Fuel: MAP Fuel High VTEC in additional mode, MAP Fuel Low VTEC in additional mode
Idle: Desired idle speed, Desired idle speed after start A, Desired idle speed after start B
Injector control: Injector scaling in additional mode
Knock Limit: Spark advance limitation for knocking High VTEC, Spark advance limitation for knocking Low VTEC
Knock sensitivity: Knock Sensitivity
Limiters: Engine speed limitation
Load limitation: Load limitation High VTEC, Load limitation Low VTEC
Overrun Cutoff: Overrun Injector Restart RPM Cut, Overrun Injector Restart RPM Recover
Sensors scaling: Lambda sensor conversion, Mass air flow sensor scaling
Spark advance: Spark advance EGR dependent High VTEC, Spark advance EGR dependent Low VTEC, Spark advance retardation to reduce torque High VTEC, Spark advance retardation to reduce torque Low VTEC, Dwell time, Ignition Dwell Angle
Spark advance corrections: Spark advance correction by intake temperature
Spark Compensation: Water Temperature Ignition Advance, Water Temperature Ignition Retard
Target Lambda: Target Lambda at full load, Target lambda in closed loop, Target lambda limit for closed loop
Throttle valve control: Driving Force in additional mode, Throttle valve position linearization High VTEC, Throttle valve position linearization Low VTEC, Enable throttle valve opening
Torque: Torque Limit Torque Limitation (Test, if found)
VTEC: Engine speed to enable VTEC (Test, if found)
Vehicle speed limitation - NO support!
DTC mask - NO support!
Supported SW list
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Модуль Honda Keihin 1.5 NA BitEdit
Модуль для редактирования калибровок автомобилей Honda с атмосферными бензиновыми двигателями объемом 1.5 л и блоками управления Keihin на базе процессора TC1782.
Поддерживаемый размер файлов: 2.5Мб
Поддерживаемые карты:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge Efficiency Low VTEC, Airmass flow through throttle body in additional mode, Exhaust back pressure after catalyst, Airmass flow through throttle body direct
Camshaft control: Target camshaft angle High VTEC, Target camshaft angle Low VTEC, Camshaft Angle at WOT High VTEC, Camshaft Angle at WOT Low VTEC
EGT: EGT Prediction MAP by Air Intake A/B
Fuel: MAP Fuel High VTEC in additional mode, MAP Fuel Low VTEC in additional mode
Idle: Desired idle speed, Desired idle speed after start A, Desired idle speed after start B
Injector control: Injector scaling in additional mode
Knock Limit: Spark advance limitation for knocking High VTEC, Spark advance limitation for knocking Low VTEC
Knock sensitivity: Knock Sensitivity
Limiters: Engine speed limitation
Load limitation: Load limitation High VTEC, Load limitation Low VTEC
Overrun Cutoff: Overrun Injector Restart RPM Cut, Overrun Injector Restart RPM Recover
Sensors scaling: Lambda sensor conversion, Mass air flow sensor scaling
Spark advance: Spark advance EGR dependent High VTEC, Spark advance EGR dependent Low VTEC, Spark advance retardation to reduce torque High VTEC, Spark advance retardation to reduce torque Low VTEC, Dwell time, Ignition Dwell Angle
Spark advance corrections: Spark advance correction by intake temperature
Spark Compensation: Water Temperature Ignition Advance, Water Temperature Ignition Retard
Target Lambda: Target Lambda at full load, Target lambda in closed loop, Target lambda limit for closed loop
Throttle valve control: Driving Force in additional mode, Throttle valve position linearization High VTEC, Throttle valve position linearization Low VTEC, Enable throttle valve opening
Torque: Torque Limit Torque Limitation (Test, if found)
VTEC: Engine speed to enable VTEC (Test, if found)
Vehicle speed limitation - NO support!
DTC mask - NO support!
Список поддерживаемых версий ПО
Внимание! Для работы необходим ключ защиты BitEdit
Основные возможности редактора:
- Подходит для использования как новичками, так и опытными калибровщиками.
- Визуализация данных калибровок в табличном, двумерном, трехмерном видах.
- Поддержка редактирования: по дельта(+/-), в процентах, установка значения.
- Поддержка умного копирования и вставки (включая множественное выделение).
- Гибкий и настраиваемый интерфейс с системой докинга.
- Возможность открывать сразу несколько карт калибровок.
- Автоматическое управления параллельными картами (они определены в модуле) с переносом изменений.
- Модульная система, позволяющая избежать лишних затрат.
Программа имеет клиент-серверную архитектуру, для работы требуется обязательное наличие подключения к сети Интернет. Активация дополнительных модулей производится в автоматическом режиме через интернет.
Указанные цены в рублях действительны только для резидентов России, Украины, Белорусии и Казахстана. Ключ без модулей не продаётся!
Загрузки
Module Honda Keihin 1.5 NA
Software module allows to edit calibrations of the Honda/Acura Petrol 1.5 normal aspirated vehicles with Keihin TC1782 ECUs.
Supported filesize: 2.5Mb.
Available maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge Efficiency Low VTEC, Airmass flow through throttle body in additional mode, Exhaust back pressure after catalyst, Airmass flow through throttle body direct
Camshaft control: Target camshaft angle High VTEC, Target camshaft angle Low VTEC, Camshaft Angle at WOT High VTEC, Camshaft Angle at WOT Low VTEC
EGT: EGT Prediction MAP by Air Intake A/B
Fuel: MAP Fuel High VTEC in additional mode, MAP Fuel Low VTEC in additional mode
Idle: Desired idle speed, Desired idle speed after start A, Desired idle speed after start B
Injector control: Injector scaling in additional mode
Knock Limit: Spark advance limitation for knocking High VTEC, Spark advance limitation for knocking Low VTEC
Knock sensitivity: Knock Sensitivity
Limiters: Engine speed limitation
Load limitation: Load limitation High VTEC, Load limitation Low VTEC
Overrun Cutoff: Overrun Injector Restart RPM Cut, Overrun Injector Restart RPM Recover
Sensors scaling: Lambda sensor conversion, Mass air flow sensor scaling
Spark advance: Spark advance EGR dependent High VTEC, Spark advance EGR dependent Low VTEC, Spark advance retardation to reduce torque High VTEC, Spark advance retardation to reduce torque Low VTEC, Dwell time, Ignition Dwell Angle
Spark advance corrections: Spark advance correction by intake temperature
Spark Compensation: Water Temperature Ignition Advance, Water Temperature Ignition Retard
Target Lambda: Target Lambda at full load, Target lambda in closed loop, Target lambda limit for closed loop
Throttle valve control: Driving Force in additional mode, Throttle valve position linearization High VTEC, Throttle valve position linearization Low VTEC, Enable throttle valve opening
Torque: Torque Limit Torque Limitation (Test, if found)
VTEC: Engine speed to enable VTEC (Test, if found)
Vehicle speed limitation - NO support!
DTC mask - NO support!
Supported SW list
Module requires security USB dongle
The main features of the editor:
- Suitable for use by both beginners and experienced calibrators.
- Visualization of calibration data in tabular, two-dimensional, three-dimensional forms.
- Editing support: delta(+/-), percentage, value setting.
- Support for smart copy and paste (including multiple selection).
- Flexible and customizable interface with docking system.
- Ability to open several calibration cards at once.
- Automatic management of parallel maps (they are defined in the module) with the transfer of changes./
- Modular system to avoid unnecessary costs.
Downloads
Если у Вас возникли вопросы по данному товару, задавайте их через форму ниже.
BitEdit
| ЧИП-ТЮНИНГ ЭБУ
« Назад
|
