|
|
PCMflash Модуль 89 — ЭБУ Bosch MG1/Denso китайских автомобилейМодуль 89 предназначен для работы с ЭБУ семейства Bosch MG1 (MG1US008, MG1UA008, MG1US708) и ЭБУ Denso, устанавливаемыми на автомобили китайских производителей. Поддерживается чтение и запись через диагностический разъём автомобиля, а также проверка и коррекция контрольных сумм. Для чтения ЭБУ дорестайлинговых Haval F7/F7x требуется прямое подключение к разъёму ЭБУ. Поддерживаемые ЭБУ и функцииBAIC 1.5л A151A1 (MG1UA008) [ЧТ/ЗП/КС] ЧТ — чтение; ЗП — запись; КС — проверка и коррекция контрольных сумм. Также поддерживаются— ЭБУ Denso автомобилей Geely — виртуальное чтение, запись, проверка и коррекция КС (с версии 1.4.7-2). Платформа Volvo не поддерживается, виртуальное чтение — для автомобилей рынка Китая; Схемы подключения в документации PCMflashСхемы подключения к модулю 89 приведены для ЭБУ Bosch MG1Uxxx и Geely Denso Gen 2 (0N50N). 📄 Документация: модуль 89 — скачать (PDF, схемы подключения) Что нужно для работыДля работы с программой требуется совместимый J2534-адаптер — рекомендуем Сканматик 3. Основной режим работы — через диагностический разъём автомобиля (OBD). Для чтения ЭБУ дорестайлинговых Haval F7/F7x требуется прямое подключение к разъёму ЭБУ и boot/bench-кабель (например, фирменный Сканматик TunerWire для Сканматик 3, 2 Pro и 2) или разветвитель. Для работы на столе удобно использовать разветвители: SUPER BOX в комплектации FULL (с двумя кабелями DB25 — с толстыми контактами и с тонкими контактами-прищепками) или MAX (FULL + коммутационная плата для изменения распиновки и подключения измерительных приборов), PowerBox for PCMflash и CombiBox для PCMflash. Разветвители подают питание и сигнал BOOT на ЭБУ автоматически по команде PCMflash. Единоразово необходимо приобрести электронный ключ PCMflash, без которого программа не работает. Ключ отдельно не продаётся. ЗагрузкиДрайвер ключа x86 - скачать ВНИМАНИЕ!!! Активация PCMflashПервая активация. В архиве «Инструкция и ПО для первичной активации ключа» находится программа GRDTRU. Сформируйте в ней файл-запрос на обновление ключа и пришлите его на почту mail@eobd.ru с указанием номера вашего заказа. Важно: не формируйте новых запросов и не переставляйте ключ в другие ПК до окончания активации. После получения файла-обновления (update) вставьте его в GRDTRU и пришлите нам полученный последний файл-ответ (answer). После этого запустите программу PCMflash, в настройках вставьте специальный код из нашего письма и нажмите кнопку «Активация». После перезапуска программой можно пользоваться. Ключ можно использовать на любых ПК. Вторая и последующие активации модулей. Оформите заказ и укажите только серийный номер вашего USB-ключа PCMflash — файл-запрос от GRDTRU присылать не нужно. После получения кода активации зайдите в настройки программы PCMflash, вставьте код и нажмите кнопку «Активация». PCMflash Module 89 — Bosch MG1/Denso ECUs of Chinese vehiclesModule 89 is designed to work with Bosch MG1 family ECUs (MG1US008, MG1UA008, MG1US708) and Denso ECUs installed in vehicles of Chinese manufacturers. Supports reading and writing via the vehicle diagnostic connector, as well as checksum verification and correction. Reading the ECUs of pre-facelift Haval F7/F7x requires a direct connection to the ECU connector. Supported ECUs and functionsBAIC 1.5L A151A1 (MG1UA008) [RD/WR/CK] RD — read; WR — write; CK — checksum verification and correction. Also supported— Denso ECUs of Geely vehicles — virtual reading, writing, checksum verification and correction (since version 1.4.7-2). The Volvo platform is not supported; virtual reading is available for vehicles of the Chinese market; Wiring diagrams in the PCMflash documentationWiring diagrams for module 89 are provided for Bosch MG1Uxxx and Geely Denso Gen 2 (0N50N) ECUs. 📄 Documentation: module 89 — download (PDF, wiring diagrams) RequirementsA compatible J2534 adapter is required — we recommend Scanmatik 3. The main mode is via the vehicle diagnostic connector (OBD). Reading pre-facelift Haval F7/F7x ECUs requires a direct connection to the ECU connector and a boot/bench cable (e.g. the genuine Scanmatik TunerWire for Scanmatik 3, 2 Pro and 2) or a breakout box. For bench work, breakout boxes are convenient: SUPER BOX in the FULL kit (with two DB25 cables — with thick pins and with thin clip pins) or the MAX kit (FULL + a breakout board for re-routing pinouts and connecting measuring instruments), PowerBox for PCMflash and CombiBox for PCMflash. The breakout boxes switch the ECU power and the BOOT signal automatically on PCMflash's command. You must purchase the PCMflash key once, without which the program does not work. The key without modules is not for sale! Contents of delivery— Software (delivered by email); Important— Please double-check what you are ordering and make no mistake with the choice: if you order the wrong module, we will not be able to help you. DownloadsDongle driver x86 - download ATTENTION!!! PCMflash activationFirst activation. The archive "Instructions and software for the initial activation of the key" contains the GRDTRU program. Create a key update request file in it and send it to mail@eobd.ru with your order number. Important: do not create new requests and do not move the key to other PCs until the activation is complete. After receiving the update file, insert it into GRDTRU and send us the resulting answer file. Then launch PCMflash, paste the special code from our email in the settings and click "Activate". After restarting, the program can be used. The key can be used on any PC. Second and subsequent module activations. Place an order and provide only the serial number of your PCMflash USB key — there is no need to send a request file from GRDTRU. After receiving the activation code, open the PCMflash settings, paste the code and click "Activate". About PCMflashWe are an official store for PCMflash: we sell the PCMflash USB dongle key with different modules. PCMflash software is very popular among chiptuners all over the world. The software allows you to identify ECUs, read and write ECUs, PCMs and automatic transmissions, and calculate checksums for Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan/Infiniti, Subaru, Honda/Acura, Hyundai/Kia, Renault, Toyota/Lexus, Citroen/Peugeot and other vehicles. It works with any J2534-compatible adapter with the appropriate drivers and libraries. The software has a modular structure and a simple, concise interface. A Guardant USB dongle key protects it against unauthorized use. It supports writing both factory (VBF, GDS) and binary (BIN) files and converting VBF/GDS files to BIN when the ECU does not support reading. For most modules, checksums can be checked and corrected when writing binary files, and the VID block can be transferred (if required). PCMFlash | ЧИП-ТЮНИНГ ЭБУ |